Aston Service Dorset : Aston Martin Lagonda Official Parts Manufacturer and Distributer.

	Pre War Lagonda DB Lagonda + Rapide DB2 + DB2/4 MkI - MkII DB2/4 MkIII DB3S DB4 + DB4 GT DB5 + DB6 DBS + AM Vantage DBSV8 + AMV8 + V8 Lagonda Virage + V8 Vantage DB7

  Suspension + Steering

  Front Suspension (Plate N)
  Rear Suspension (Plate O)
  Steering Gear (Plate P)

  Engine

  Fuel, Cooling + Exhausts

  Transmission

  Brakes + Pedal Gear

  Electrical + Instruments

  Chassis, Frame, Body, etc.

For all Parts Catalogues, Workshop Manuals and Instruction Books please follow the link to the technical publications page.

Below is a selection of the parts that we can provide for the suspension, for anything else please contact us

The front suspension is independent with helical coil springs, telescopic shock absorbers, transverse wishbones and ball jointed king pins.

		20-23-114 20-23-116 20-23-118 20-23-168		Ball Joint - Brake Reaction Strut Ball Joint Bearing Upper and Lower, also does 20-23-117 Retainer - Ball Joint Plug - Ball Joint Housing

		20-23-119 20-23-161 20-23-140		Locating Bolt - Ball Joint Gaiter Upper Wishbone Spindle

		20-23-152 20-23-101		King Pin - Left Hand up to Chassis No. 250 King Pin - Left Hand from Chassis No. 251

		20-23-120 20-23-121 20-23-124 20-23-125		Bush - Wishbone Spindle - Lower Wishbone Lower Ball Seating - King Pin Thrust Pad - King Pin

		20-23-162 20-23-126 20-23-127 20-23-128		Shim - Lower Thrust Pad Spring Spring - King Pin Lower Thrust Pad Lower Spring Retaining Cap Gaiter - King Pin

		20-23-129 690524 20-23-136 20-23-137		Anchor Bolt - Road Spring Tension Pin Upper Ball Seating - King Pin Bearing Cap - King Pin

		20-23-131 20-23-132		Shock Absorber Complete Front Road Spring

		20-23-138 20-23-004 20-23-139 125598		Spring - King Pin Upper Thrust Pad Upper Spring Retaining Cap Assembly Adjusting Screw Slotted Nut, 5/8" UNF

		20-23-163 20-23-164 112390 20-23-154		Shim, Upper Spindle .020" Shim, Upper Spindle .050" Circlip, Internal Ball, King Pin, Upper

		20-23-155 20-23-160 122306 122305		Ball, King Pin, Lower Top Gaiter Oil Seal - Front Hub Taper Roller Bearing - Inner Front Hub

		125591 20-23-159 20-23-142 20-23-147		Taper Roller Bearing - Outer Front Hub "D" Washer Rubber Bush Link, Anti-Roll Bar

		20-23-150 20-23-148 20-23-149		Washer, Inner Rubber Bush, Anti-Roll Bar Link Washer, Outer

		123115 20-23-167 690087		Nut, Nyloc 5/16" UNF Rebound Rubber Tap Washer

Back to top

The rear suspension consists of a live hypoid bevel axle mounted on parallel trailing links and located transversely by Watts linkage. There are helical coil springs mounted behind the axle with large double acting piston type shock absorbers.

20-26-125

20-26-123

20-26-152

20-26-153 Bump Stop

Check Strap

Rear Hub - Right Hand Side

Rear Hub - Left Hand Side

20-26-119

20-26-120

20-26-118 Bolt - Upper Radius Arm

Bolt - Lower Radius Arm

Bush - Radius Arm

REAR01 Conversion Kit to replace lever-arm shock absorbers

Also suits DB5 and DB6

20-26-135

20-26-140

20-26-141 Bolt, Radius Arms-Axle

Bush, Swinging Link, Centre

Bush, Swinging Link, Outer

20-26-146

20-26-148

20-26-154 Bush, Watts Link

Bolt - Watts Link to Frame

Insulating Ring

20-26-138 Front Road Spring

20-26-155

20-26-001 Link Assembly, Shock Absorbers

Radius Arm Assembly

Back to top

The rack and pinion steering gave a turning circle of approximately 34 ft.

20-25-139

20-25-140

20-25-112

20-25-138 Mounting Clamp - Bulkhead

Gaiter - Steering Column

Top Bearing Housing

Rubber Sleeve

20-27-120P

55-50-600 Poly Bushes for the Upper and Lower Wishbone

Solid Steering Rack Mounting, fitted together with the poly Bush above gives a much better steering response

20-24-130

20-24-128

20-24-131 Ball Joint - Track Rod End

Gaiter - Steering Rack

Mounting